For a professional mechanic, resolving this error code is as simple as cleaning or replacing the damaged parts correctly. This is especially the case for repairing camshaft timing components, which may include taking the timing chain apart to replace a malfunctioning actuator.
Code P0010 is triggered when the ECM attempts to adjust the Bank 1 intake camshaft timing by utilizing one of these valves, and it detects an electrical issue in either the circuit going to the valve or the windings of the solenoid in the valve itself.
How much does it cost to fix P0010 code?
Possible repairs for P0010 & Costs
Here are some of the possible repairs and their approximate cost: Variable Valve Timing control solenoid: $500 – $600. Camshaft position sensor: $120 – $300. Wiring repair or replacement: $100 – $1000.
What does a camshaft position actuator circuit open bank 1 mean?
What Does the P0010 Code Mean? Code P0010 stands for “A” Camshaft Position Actuator Circuit (Bank 1). The code indicates that your car’s primary computer, which is also referred to as the powertrain control module (PCM), perceives a problem with one of the engine’s VVT solenoids.
Can code P0010 be fixed? – Related Questions
How do you reset a camshaft sensor?
How to reset the camshaft position sensor? Evidently, you cannot reset a camshaft position sensor. Therefore, you will need to replace the component if your camshaft malfunctions (check engine light on, acceleration issues, sputtering and stalling, etc.).
What does P0010 permanent code mean?
P0010 is a generic OBD-II code indicating an issue with the engine control module (ECM) detecting a variation in the mechanical timing between the crankshaft and bank 1 camshaft. The timing issue is typically detected during higher RPMs of the engine when the ECM attempts to adjust valve lift during higher speeds.
Where is camshaft position sensor a bank 1 located?
Can I drive with a camshaft position sensor problem?
The short answer is yes, it is safe to drive with a bad camshaft sensor, but it’s not good for your engine long-term. You’ll likely see a higher fuel consumption and poorer engine performance the longer you wait to get it fixed.
What does bank 1 mean on an engine?
In the automotive world, Bank 1 refers to the number one cylinder bank, which means it is the bank where the number one cylinder is located. On an inline four-cylinder engine, this is the only cylinder bank.
Where is the camshaft position correlation bank 1 sensor A?
On most vehicle applications, the camshaft position sensor is located near the cylinder head so that the CMP is opposite the timing rotor attached to the engine camshaft.
Which side is bank1 sensor?
Which side of the engine is bank 1?
Most commonly, bank 1 houses the front most cylinder on the engine cylinder 1, and bank 2 is the opposite side of the engine.
How serious is a camshaft position sensor?
Driving with a Bad Camshaft Position Sensor
Continuing to drive the car can lead to additional failures in other areas of your car, which can end up causing you to have a higher service bill. Your car can also stall when the sensor is failing. This can be dangerous to you, your passengers, and everyone on the road.
What makes a camshaft sensor go bad?
There are a number of reasons your camshaft sensor might break down: grime and oil in the engine, water damage, bad wiring, and overheating can all cause a camshaft sensor to go bad. The biggest thing to do to avoid this is to take care of your car.
Can low oil cause camshaft position sensor?
If the oil level is very low, to the point where the engine overheats however, yes. Excessive heat can cause a camshaft position sensor to fail. More likely in a “low oil level” situation is for the camshaft, lifters, or camshaft variable timing actuator to fail due to inadequate oil pressure and lubrication.
What are the symptoms of a faulty camshaft sensor?
A glowing check engine light, stalling, poor acceleration and bad fuel mileage are all possible signs your camshaft position sensor may be failing. Gone are the days of carburetors and distributors, replaced by a variety of sensors that help a car’s computer get the maximum performance out of the engine.
Definitely don’t submerge the sensor. Cam/Crank sensors are usually hall-effect magnetic sensors that wear over time due to heat. Cleaning them will not commonly make them work any better.
How much does it cost to replace both camshaft sensors?
Cost to Replace a Camshaft Sensor
A camshaft position sensor replacement is not an expensive job, if diagnosed properly. Some vehicles may have a lower cost, but expect a cost of between $200 and $400 for mainstream cars to replace the camshaft position sensor.
How do you test a camshaft sensor?
How do you reset your car after changing camshaft sensor?
Unfortunately, there’s no way to reset a camshaft position sensor. If you’re having camshaft issues (check engine light on, acceleration trouble, sputtering and stalling, etc.), you’ll have to replace the part entirely.