So now you know – it’s definitely possible to install a subwoofer and amplifier to your factory system, and still have it sounding good. If you’d like to know more about how to get a killer system set-up in your car without swapping your stereo, give us a call at 510-527-9888.
How do you hook up a subwoofer to a car stereo amp?
Connect the subwoofer RCA cables to the amplifier.
Connect the left channel on the subwoofer to the left channel on the amplifier and the right channel on the subwoofer to the right channel on the amplifier. If there is a separate power cord for the sub, you may need to attach this to the amp as well.
How do I connect my subwoofer to my stereo?
If you are using your subwoofer with a home theater receiver, the connection is simple: Just run an audio interconnect cable like this one from the receiver’s subwoofer output to the subwoofer’s line input (pictured above). If the subwoofer has an input labeled LFE, use that one.
What is the best way to hook up a subwoofer?
The optimal connection for a standard powered subwoofer is to use the RCA (Phono) “sub” or “woofer” line out found on home theater receivers and pre-amps. Some subwoofers offer “High Level inputs” (speaker wire connections) for use with a receiver or pre-amp without a sub RCA connection.
Can I just add a subwoofer to my car? – Related Questions
Can I install subwoofer without amp?
Unless you have a system in your car or boat that is already powering a subwoofer, you’ll need to find an amplifier that will power your sub. Your head unit will typically provide a low-power signal (RCA output) that can be used for an amplifier to power your subwoofer.
What do you need to connect a sub?
You will need either a receiver or a preamplifier and amplifier. Using a subwoofer cable (RCA cable), connect the subwoofer to the AV receiver by running the cable from the receiver’s subwoofer output to the subwoofer’s line input.
Where do I plug my subwoofer into my receiver?
The preferred method of connecting a subwoofer is through the subwoofer output (labeled SUB OUT or SUBWOOFER) of a receiver using an LFE (Low-Frequency Effects) cable. Almost all home theater receivers and processors and some stereo receivers have this type of subwoofer output.
Why does subwoofer have left and right input?
The left and right inputs on your subwoofer are there to give you another level of control over the sound it creates. In the end, both the left and right sides come together in an LFE cable, allowing the subwoofer to evenly output, and have more precise control over the sound it emits.
Should a subwoofer be on the floor?
Placing a subwoofer in the corner of a room can increase its output, making it sound louder. The great thing about a subwoofer (especially a wireless subwoofer) is it can be situated almost anywhere on your floor space. There is no formula for locating the best spot. And, it’s truly your personal preference.
What frequency should I set my amp to for subs?
Subwoofers: 70-80 Hz (low pass), the most essential purpose of a subwoofer crossover is to block midrange sounds. Car main speakers: 50-60 Hz, the most critical element in main speaker crossovers is to block low-end bass (frequencies 80 Hz and below) 2-way speakers: 3-3.5 kHz (high pass)
What happens if the gain is too high?
What Happens If Gain Is Too High? If the gain is too high at the input stage, your audio will reach the point of distortion or clipping. This can be a good or bad thing depending on what you are going for, as you might want to get some distortion with an amplifier, though you might want a clean tone for digital audio.
How do I get more bass from my subwoofer?
It is recommended that for optimal quality sound, you should place your subwoofer within 8-12 inches of a wall, facing outwards towards the rest of the room. For even more output, consider placing your subwoofer in the corner of your room, as it can significantly increase the overall sound due to the positioning.
What Hz is best for bass?
BASS AND UPPER BASS (40-80 Hz/Eto E2)
For normally tuned bass guitar and upright double bass, note fundamentals extend down to E1, (open E). I would consider bass arbitrarily to be below C2 (65.41 Hz). That is two octaves below middle C. The fundamental of a note is its musical pitch.
What subwoofer has the deepest bass?
Our Subwoofer Picks
- Best Overall Subwoofer: SVS SB-1000 Pro.
- Best Budget Subwoofer: Monoprice 9723.
- Best High-End Subwoofer: SVS SB-3000.
- Best Wireless Subwoofer: Sonos Sub.
- Maximum Bass for Home Theater: Seaton Sound.
- Subwoofer with the Deepest Bass: KEF KC62.
- A Great Subwoofer for Music: RSL Speedwoofer 10S.
Which equalizer setting is best for bass?
Bass exists between about 20Hz and 200Hz.
Every musical note corresponds with a frequency. If you want to maximize your bass-heavy music, you need to adjust your equalizer within the 20-200Hz range by boosting the decibels (dB) in that range.
What is the perfect equalizer setting?
The best equalizer setting is one that is turned off or one that is set to “flat”, meaning that all dials are set to zero. Equalizers distort the sound of the original master recording. However, they can be useful as a last-resort when compensating for poor speakers or headphones.
Should treble be higher than bass?
To Get Rid of Mid-Frequency Muddiness
Mid-frequency muddiness in the 400 – 800 Hz frequency range can be a major headache for music producers. By keeping the treble higher than the bass, you won’t only listen to the 400 – 800 Hz sounds, eliminating the muddiness.
How do you use an equalizer for beginners?
Getting started with EQ
Set the centre, corner or cutoff frequency you want to adjust for a given band, then raise or lower the gain control to cut or boost the volume of that frequency and a range of frequencies adjacent to it, as determined by the bandwidth or ‘Q’ control.
What should bass and treble be set at in car?
Bass frequencies are generally between 60 to 120 hertz, mids between 400 to 2,500 hertz, and treble between 8,000 to 15,000 hertz.
How can I make my bass sound better in my car?
Just follow these simple steps for great bass:
- Remove the distortion.
- Flatten the signal, open the low-pass filter.
- Adjust the subwoofer gain and low-pass filter.
- Adjust the bass boost and subsonic filter.
- Match the subwoofer level to the receiver volume.