How do you reset the radio in a 2013 Kia Sportage?
by
Just had the same issue today in our 2013 Sportage. There’s a reset button to the right of the CD slot.Use a small point tip to hit the reset button & should get your sound back.
Locate the small reset button hole on the faceplate of the radio. It is usually located to the lower-right of the display, but is sometimes located at the upper-right of the display. 2. Use a paper clip or pen tip to press and hold the “Reset” button for 1 second.
Why did my car radio suddenly stop working?
The most likely reason for your radio’s sudden death is a blown fuse. All car radios have at least one fuse that protects it from power surges coming from somewhere else in the vehicle. The first thing you should do when your radio stops working is check its fuses and replace any that have blown.
How do you reset the radio in a 2013 Kia Sportage? – Related Questions
How do I know if my radio fuse is blown?
Remove the fuse from its holder. In some cases you may need a small screwdriver to unscrew the fuse holder cap. Look at the fuse wire. If there is a visible gap in the wire or a dark or metallic smear inside the glass then the fuse is blown and needs to be replaced.
Why does my radio have power but wont turn on?
Most probably, the power wires of the stereo are in bad condition. While one power wire is always out, the other only heats up with the ignition key. But, if their functions get inverted, the stereo will stop working. If these power wires do not have any voltage, it is time to replace them.
What could be some reasons a car radio isn’t turning on?
Some of the most common issues include a blown fuse, bad or damaged wiring, and anti-theft modes that are often triggered when the battery dies. In order to track down the reason that your car radio won’t turn on, you’ll want to tackle each of these potential issues one at a time.
Can a low car battery cause the radio to not work?
While a dead battery, or a jump start, can result in a car radio that doesn’t work, it could also be a pure coincidence.
What causes blown radio fuse?
Possible Cause: Possible short in wiring. Action: Check wiring to be sure no power wires (red, yellow, blue, or blue/white) are touching metal. Possible Cause: Possible incorrect fuse.
Turn your car on, but do not start the engine. Turn the radio off. Hold the radio power button down for a few minutes until it resets.
How do I reset my radio manually?
Method 1:
Turn on the ignition.
If the screen says CODE then turn off the radio.
Press and hold the Power/Volume button for 40-50 seconds.
It should unlock your radio in under a minute.
How do I reset my car without disconnecting the battery?
How to Reset the ECU/ECM Without Disconnecting the Battery:
Pop the hood and locate the fuse box.
Remove the fuse cover, then the ECU/ECM fuse.
Leave the fuses for at least 10 seconds or up to 15 minutes.
Reinstall the car computer fuse and replace the fuse cover.
Take out your vehicle for a test drive.
Why does my radio turn on but no sound?
If your radio is turning on but there is no sound. First check radio functions, be sure you have an audio source selected like Radio. If using AUX, USB or BT AUDIO be sure you have a device connected to the correct input. Be sure the radio is not Muted.
What can cause a radio not to work?
5 REASONS WHY YOUR CAR RADIO MAY HAVE STOPPED WORKING IN THE PORTLAND AREA
Your Radio May Be Equipped with Anti-Theft Technology.
Antenna or Tuner has a Problem.
There’s a problem with the Speakers or Their Wiring.
There’s a Problem with the Wiring.
A Fuse Needs to be Replaced.
How do you diagnose a car radio problem?
Use a multimeter to test the stereo’s two power wires. This will help you determine if there is broken or faulty wiring. One power wire provides power to the stereo’s memory and is always hot. While the other wire is only hot when you turn on the ignition.
Hardware problems can be caused by outdated or malfunctioning drivers. Make sure your audio driver is up to date and update it if needed. If that doesn’t work, try uninstalling the audio driver (it will reinstall automatically). If that doesn’t work, try using the generic audio driver that comes with Windows.
How do I reset my sound system?
Unplug the AC power cord (mains lead) from the system, then plug it back in. Press the (POWER) button to turn on the system. At the same time, press and hold the FUNCTION/ PAIRING and – (VOLUME minus) buttons on the system for more than 5 seconds.
How do I get my sound to work again?
How do I fix “no sound” on my computer?
Check your volume settings.
Restart or change your audio device.
Install or update audio or speaker drivers.
Disable audio enhancements.
Update the BIOS.
How do I get my sound back on my?
How do I fix disabled sound?
Press Windows + R, type “devmgmt. msc” in the dialogue box and press Enter. Once in the device manager, right-click on the audio device which is disabled and select “Enable device”. You can instantly see which device is disabled by checking the black arrow beside it pointing downwards.