Suitable from birth until approximately 3 years, all-in-ones are a flexible system made up of a chassis, rearward and forward facing seat, carrycot and infant carrier adapters.
At Britax Römer we are dedicated to your child’s safety. That’s why we were involved in the first legislation for the requirement of child car seats, ECE R44, and developed the first ISOFIX car seat to make installation easy and intuitive.
Can Britax Romer be used without ISOFIX?
The seat is approved for use in all vehicles that meet ECE R14 and R16 regulations. Any Isofix car seat must use the Isofix anchorage points including the top tether or foot support and the vehicle’s handbook must state that the car is suitable for “Universal Isofix child seats”.
What age is the Britax Romer car seat for? – Related Questions
Does the Britax Romer recline?
Recline position for all ages
The recline position provides a comfortable sleeping position for your child. Simply adjust the seat before fitting it in your car.
How do you fit a Britax Romer Isofix?
How do you fit a Britax Romer rear facing car seat?
How do you install a Britax Isofix car seat?
How do you install a Britax car seat forward facing?
How do you install a Britax rear facing car seat?
How long are carseats good for?
Every car seat brand is different, but many manufacturers set an expiration date of six years. Therefore, you shouldn’t use or buy a car seat that’s older than six years, or one past the date specified on your particular model.
Do you have to tether a rear facing Britax?
Britax recommends, but does not require, use of the tether while rear facing. An anti-rebound bar is now available for purchase from Britax. This is used to control rebound and can be used on all ClickTight convertibles in all vehicles without restriction. Advocate CT forward facing tether.
How do you install a Britax car seat without a base?
Is it safe to use a car seat without the base?
Typically, you don’t need the base to properly use your car seat — it’s just a convenience. To install without the base, just thread the seat belt through the grooves on the side of the seat and tighten in the same manner as above.
All six of the Britax rear-facing infant seats will have ALL of these characteristics, to further explain why we LOVE Britax! Interchangeable bases: All B-safe 35/ARB/Gen2/Gen2 with ARB are compatible with all infant seats (excluding the discontinued B-Safe.)
Does Britax allow latch borrowing?
Exceptions: Graco excludes convertible, harness-to-booster, and all-in-one car seats with push-on LATCH connectors. Britax allows for center lower anchor borrowing with car seats produced before 2015 and only if specified in the car-seat manual.
Does car seat go behind driver or passenger?
Install in the Backseat
The car seat should always be installed in the back seat. That is the safest spot for your baby. If you can, put the car seat in the center seat. If not, it is fine behind either the driver or passenger side.
Is it safe to install car seat in the middle?
The center of the back seat is statistically the safest place in the car. Research from real crashes shows that the center is safest – particularly because you can’t take a direct impact in the center. One study of kids 0-3 years old found that kids sitting in the center are 43% safer than those sitting on the side.
Does Britax allow overhang?
How far can my car seat overhang the vehicle seat? It is important that the base of the child seat rests completely flat on the vehicle seat with no side overhang. As seen in the illustration, it is permissible to allow up to 3 in.(7.6 cm) of the base to hang over the front edge of the vehicle seat.
Look for a label on the side of the seat that says “This child restraint system conforms to all applicable Federal Motor Vehicle Safety Standards” and “This restraint is certified for use in motor vehicles and aircraft.” All Britax harnessed car seats, including infant car seats, convertible car seats, and combination