Code P0010 is triggered when the ECM attempts to adjust the Bank 1 intake camshaft timing by utilizing one of these valves, and it detects an electrical issue in either the circuit going to the valve or the windings of the solenoid in the valve itself.
The P0010 engine code shows that there’s an issue with some of your engine’s key components, but it won’t immediately endanger you on the road. Depending on the exact problem that triggered the code, you may be able to continue driving the car without significant trouble for a while.
Where is the camshaft actuator located?
The exhaust camshaft actuator features a black electrical plug and is located closer to the rear of the vehicle on the top of the cylinder head.
What does a camshaft position actuator circuit open bank 1 mean?
What Does the P0010 Code Mean? Code P0010 stands for “A” Camshaft Position Actuator Circuit (Bank 1). The code indicates that your car’s primary computer, which is also referred to as the powertrain control module (PCM), perceives a problem with one of the engine’s VVT solenoids.
What causes code P0010? – Related Questions
How do you reset a camshaft sensor?
How to reset the camshaft position sensor? Evidently, you cannot reset a camshaft position sensor. Therefore, you will need to replace the component if your camshaft malfunctions (check engine light on, acceleration issues, sputtering and stalling, etc.).
Can I drive with a camshaft position sensor problem?
The short answer is yes, it is safe to drive with a bad camshaft sensor, but it’s not good for your engine long-term. You’ll likely see a higher fuel consumption and poorer engine performance the longer you wait to get it fixed.
Where is camshaft position sensor a bank 1 located?
A camshaft position sensor (CMP) is essentially a component in the format of a cylinder, which is often located on the outside of the front cover (at the front of the engine under the valve cover).
What does Bank 1 mean on an engine?
In the automotive world, Bank 1 refers to the number one cylinder bank, which means it is the bank where the number one cylinder is located. On an inline four-cylinder engine, this is the only cylinder bank.
Where is the camshaft position correlation Bank 1 sensor A?
On most vehicle applications, the camshaft position sensor is located near the cylinder head so that the CMP is opposite the timing rotor attached to the engine camshaft.
There are a number of reasons your camshaft sensor might break down: grime and oil in the engine, water damage, bad wiring, and overheating can all cause a camshaft sensor to go bad. The biggest thing to do to avoid this is to take care of your car.
What are the symptoms of a faulty camshaft sensor?
If your vehicle idles roughly, stalls frequently, has a drop in engine power, stumbles frequently, has reduced gas mileage, or accelerates slowly, these are all signs your camshaft position sensor could be failing.
Can low oil cause camshaft position sensor?
If the oil level is very low, to the point where the engine overheats however, yes. Excessive heat can cause a camshaft position sensor to fail. More likely in a “low oil level” situation is for the camshaft, lifters, or camshaft variable timing actuator to fail due to inadequate oil pressure and lubrication.
What happens if you don’t replace camshaft sensor?
How do you test a camshaft sensor?
What to do after replacing camshaft sensor?
After changing the sensor remember to cancel the error codes stored in the engine controller after the failure by means of a diagnostic scanner. If fitted properly, a new sensor should restore correct operation of the engine. The sensor itself is not repairable and cannot be reused in the event of a failure.
Do you have to disconnect battery to change camshaft position sensor?
Disconnect your negative battery cable.This should be done any time you work with sensors or electrical components. It may be easiest to remove and replace the camshaft sensor from under your vehicle, but it can also be done from the top by removing the air filter housing.
The most common cause is a failing or a defective camshaft position sensor. Other problems can include circuit issues, like loose connections or damaged wiring, errors with the PCM, or a damaged reluctor wheel for the camshaft position sensor.
How much does it cost to replace both camshaft sensors?
A cam sensor problem diagnosis and replacement will usually cost between $200 and $400 at a trusted local shop. If you have a luxury vehicle or use a dealership to service your vehicle, that cost can be as much as double.
How long does it take to replace a camshaft sensor?
A camshaft sensor is one of the essential parts of your vehicle, so much so that you probably won’t be able to drive at all with a faulty one. Fortunately, the part is relatively inexpensive compared with a lot of other vehicle parts, and it only takes about an hour or so for a mechanic to replace it.