Due to the chemical properties of PTFE hose it’s a perfect fit for using braided lines for your transmission fluid lines.
What does a transmission hose do?
The transmission oil cooler hose on a car helps to carry the transmission fluid from the transmission to the transmission cooler. The oil cooler is designed to lower the temperature of the transmission fluid to make it easier for the internal parts of the transmission to use.
What happens when a transmission hose breaks?
If they break or develop a leak, you will lose transmission fluid, leaving your car vulnerable. Thankfully this is a fairly simple fix, and most transmission line repairs cost between $100 and $500 dollars.
Can you use power steering hose for transmission hose?
So you can probably use power steering hose in a transmission oil cooler application, but not vice versa, at least not in a pressure line application. Watch out, too, for higher temperatures due to close routing near the exhaust in some power steering applications.
What type of hose can I use for transmission line? – Related Questions
Can I use fuel line as transmission line?
Fuel line hose will not hold ATF for long. Get something specifically for hydraulic fluid or tranny line. Mike W. Fuel line will work just fine on the low pressure side.
Can you use aluminum tubing for transmission cooler lines?
Fragola 3/8″ Outside Diameter Aluminum AN -6 Tubing Typically Used For Fuel Or Transmission Cooler. -6 lines are commonly used for fuel or transmission oil coolers. For AN -6 fittings you’ll need to use a 37° flaring tool.
Is a power steering return hose high pressure?
The high-pressure (supply) hose carries high-pressure oil from the power steering pump to the steering gear. The low-pressure (return) hose carries oil from the steering gear back to the pump or its reservoir.
Can you use hose clamps on transmission cooling lines?
Expert Reply: The hose clamp should be totally fine. I’ve had them used to install aftermarket coolers on my car for over a decade and they are still holding up. Most likely yours was just too loose and now that it’s tightened up it will be totally fine.
What is the diameter of a power steering hose?
Power steering pumps require a hose with a vacuum rating of 28 INCHES/HG on the inlet side, and a minimum ½”inside diameter. This is required to keep the hose from collapsing at higher RPMs.
What kind of hose can withstand brake fluid?
EPDM hose is the only rubber hose which is compatible with brake fluid. No other hose should be used due to brake fluid contamination.
Can you use transmission hose for brake fluid?
You can only use a brake hose at each wheel. Up to 2,000 pounds per square inch of pressure in the hose when the brakes are being used on your car. Brake hose is highly reinforced so it can take the high pressure.
Can I use braided hose for brake lines?
Benefits of Braided Brake Lines
The main benefit of braided brake lines is that they help improve performance by reducing the issue of swelling, most commonly associated with the standard rubber brake lines. Over time and extensive use, rubber lines can swell under the pressure caused by applying the brakes.
Can you use rubber hose on a brake line?
For a car or motorcycle, rubber brake hoses are ideal. Although they expand when pressure is applied heavily to them, they still maintain integrity and strength for your braking system. In fact, the pressure of our rubber hoses are tested to 3000 p.s.i.
What rubber is resistant to brake fluid?
Unlike Viton® O-rings, Ethylene Propylene Rubber (EPR) O-rings are suitable for use with corrosive Skydrol hydraulic fluid, as well as steam, water, silicone oils, brake fluids and alcohols. This material is known to display good heat and compression resistance.
Does brake fluid react with rubber?
All polyethylene glycol-based fluids will not harm healthy rubber parts. Also, the additive packages will not damage or distort any rubber parts. Even if an older rubber part that has a high concentration of natural rubber, they will not be damaged by new DOT rated brake fluids.
Is it OK to use compression fitting on brake line?
DO NOT USE COMPRESSION FITTINGS to join brake lines. Compression fittings are designed for lower-pressure lines such as those used for fuel, compressed air, and water. These fittings are commonly made of brass, but they’re complicated.
When should you not wear compression hose?
“If you have peripheral vascular disease affecting your lower extremities, you should not wear compression socks,” he says. “The pressure provided by compression socks may make ischemic disease worse.
Why are compression brakes banned?
The use of engine compression brakes may cause a vehicle to make a loud “growling”, “machine gun”, or “jackhammer” like exhaust noise, especially vehicles having no mufflers, which has led many communities in the United States, Canada, and Australia to prohibit compression braking within municipal limits.