Try switching off your cell phone, resetting it or removing the battery, then trying again. Try deleting your device from SYNC and deleting SYNC from your device, then trying again. Always check the security and auto accept prompt settings relative to the SYNC Bluetooth connection on your cell phone.
On SYNC, turn Bluetooth Off, then On. Press the Phone button > scroll to System Settings > Press OK > scroll to Bluetooth Devices > Press OK > select Off > select On. If this does not work, continue to steps 3 and 4. Manually connect SYNC with the phone.
How do I force my Ford Sync to reset?
Remove the navigation chip or SD card, if applicable.
Touch the GEARS found on the lower right center of the home screen.
The first and easiest thing you should try to do to stop Ford Sync not working at all is simply resetting the connection. To do this, first go to your phone’s settings and turn Bluetooth off and then back on. Following this, go to your Sync’s settings and do the exact same thing.
Why has my Ford Sync stopped working? – Related Questions
How do I troubleshoot no sync?
NO SYNC
Ensure that your phone line is working normally and free of noise or interference.
Try and connect the modem/router to the BT test socket, leaving all other equipment disconnected.
Whilst in the test socket, try an alternative microfilter to ensure it is not the filter that has failed.
What do I do if my sync button doesnt work?
Fix Xbox Sync Button Not Working with Top 5 Fixes [Partition
Fix 1: Check the Status of the Controller.
Fix 2: Re-sync the Controller.
Fix 3: Update the Controller.
Fix 4: Hard Reset the Xbox Console.
Fix 5: Pair the Console with a Micro USB Cable.
How do I restart my Sync system?
To perform a System Reset, press and hold the Seek Up (>>|) button while pressing and holding the Radio Power button. After approximately 5 seconds the screen will go black. Allow 1-2 minutes for the system reset to complete. You may then resume using the SYNC 3 system.
How do I reset my car stereo sync?
Press Settings on your vehicle’s SYNC screen.Choose General.Scroll down and press Master Reset. A message confirming that all system settings will be erased and reset to factory defaults will appear.
With the ignition OFF, disconnect the power to the SYNC module buy either disconnecting the vehicle battery or the large 54 pin connector at the back of the module.
Reconnect the power after 30 seconds.
Turn the ignition on and wait for the system to boot.
Does Sync have a fuse?
Engine control relay. Heated rear window. Ignition 15. The fuse panel is on the right side below the glove box.
Fuse Specification Chart.
Fuse or relay number
Fuse amp rating
Protected components
F67
7.5A
SYNC, Multifunction display, Global positioning system module.
F68
—
Not used.
How do I unfreeze my Ford Sync?
How do I manually update Ford Sync?
How do I install SYNC®* updates using a USB? Visit the SYNC and Navigation Update page.Enter your Vehicle Identification Number (VIN) and select Check for update.Select the drop-down under SYNC UPDATES.
How do I update my Ford Sync?
Steps for upgrading your Ford SYNC Software
Scroll to “SYNC-Settings” and press “OK.” Next, scroll to “Install on SYNC” and also press “OK” when prompted. You’ll see a prompt that appears on your screen used to verify your SYNC update. Press “Yes” to continue.
How do I reset my Ford Sync Bluetooth?
Will disconnecting battery reset Ford Sync?
Turn off the engine on the vehicle. Disconnect the vehicle’s battery and wait for about 30 seconds. Reconnect the battery after that period. Start the engine and wait for the system to reboot.
When I press Reset Sync Data nothing happens?
It is normal for nothing to appear to happen when you tap the Reset Sync Data button. The process runs in the background, invisibly to you, so allow some time afterwards for it to complete. Keep in mind that there is no Contacts app on Apple Watch.
Make sure that your Bluetooth accessory and iOS or iPadOS device are close to each other. Turn your Bluetooth accessory off and back on again. Make sure that your Bluetooth accessory is on and fully charged or connected to power. If your accessory uses batteries, see if they need to be replaced.
Why is my Bluetooth not syncing with my car?
SOLUTION: Ensure your device allows the contacts to sync. Tap ‘Settings’, then ‘Bluetooth’ and find the vehicle with the pairing issue. Tap the ‘i’ icon beside the vehicle and ensure all of the boxes are checked, including ‘Sync Contacts’!
How do I SYNC my phone to Ford Sync?
Step-by-step Ford Bluetooth Setup Guide
Make sure Bluetooth is activated on your mobile device.
On your SYNC multimedia system, press Phone > Add Phone.
On your mobile device, select your Ford SYNC system in the Bluetooth menu.
Your mobile device and Ford SYNC system are now connected via Bluetooth.
How do I turn on Ford Sync on my iPhone?
Here’s how to pair your iPhone with SYNC with MyFord Touch:
Start your vehicle and power on your phone.
Enable your phone’s Bluetooth® feature:48
Meanwhile, on your vehicle’s touchscreen, SYNC will have listed any devices that are already paired.
Go back to your phone’s Bluetooth settings, and scan for devices.
How do I activate Ford Sync?
How do I activate FordPass™ Connect using SYNC®* 3?
Tap Vehicle Details in the FordPass App.
Tap Activate Vehicle.
Go to your vehicle and start the engine.
Allow up to 90 seconds for the prompt to appear on your vehicle’s SYNC screen.
Press Allow on your vehicle’s SYNC screen to activate FordPass Connect.