For instance, a P0012 on a 2005 Ford F-150 can be resolved by topping up the engine oil, if that’s what’s triggering the issue. Switching out the timing chain or replacing the engine assembly are also confirmed fixes for this specific code on a Ford.
The P0012 engine is a sign of serious trouble with your engine. Don’t try to drive a car with this trouble code — take it to a trusted mechanic as soon as possible to avoid further damage.
What is P0012 permanent code?
P0012 is an OBD-II generic trouble code which indicates a vehicle’s ECM (engine control module) has detected the intake camshaft timing on Bank 1 (number 1 cylinder side of engine) does not correspond with the intake camshaft timing (in degrees) which the ECM expected to find; the camshaft timing is over-retarded,
How do I fix the code P0012 on my Ford? – Related Questions
Will an oil change fix P0012?
Common P0012 Diagnosis Mistakes
Prematurely replacing any component when the issue can be resolved by changing the oil and filter and adjusting the oil level to the correct level per your vehicle’s manufacturers specifications.
How do I reset my camshaft sensor?
How to reset the camshaft position sensor? Evidently, you cannot reset a camshaft position sensor. Therefore, you will need to replace the component if your camshaft malfunctions (check engine light on, acceleration issues, sputtering and stalling, etc.).
What causes camshaft timing to be off?
The ignition timing error is typically caused by damage internally like the pistons or valves inside the engine. A loose or weak engine timing belt that jumps time can cause the ignition timing to be off.
What can cause a camshaft sensor code?
The most common cause is a failing or a defective camshaft position sensor. Other problems can include circuit issues, like loose connections or damaged wiring, errors with the PCM, or a damaged reluctor wheel for the camshaft position sensor.
What causes camshaft position timing over advanced?
These are the most likely causes: The camshaft timing is off. The valve control solenoid is stuck open. The valve control solenoid system has faulty or damaged wiring.
What causes exhaust camshaft position timing?
The following are the most likely causes: The camshaft’s timing is incorrect. The valve control solenoid has failed and is stuck open. The valve control solenoid system’s wiring is faulty or damaged.
A camshaft position sensor replacement is not an expensive job, if diagnosed properly. Some vehicles may have a lower cost, but expect a cost of between $200 and $400 for mainstream cars to replace the camshaft position sensor.
Can a camshaft position sensor mess with your transmission?
Engine Misfires: A failing camshaft position sensor can cause your engine to misfire. Transmission Shifting Problems: The data sent to the engine control module can stop the transmission from shifting properly.
Can I drive with a camshaft position sensor problem?
The short answer is yes, it is safe to drive with a bad camshaft sensor, but it’s not good for your engine long-term. You’ll likely see a higher fuel consumption and poorer engine performance the longer you wait to get it fixed.
What are the signs of a failing cam sensor?
A glowing check engine light, stalling, poor acceleration and bad fuel mileage are all possible signs your camshaft position sensor may be failing. Gone are the days of carburetors and distributors, replaced by a variety of sensors that help a car’s computer get the maximum performance out of the engine.
Can low oil cause camshaft position sensor?
If the oil level is very low, to the point where the engine overheats however, yes. Excessive heat can cause a camshaft position sensor to fail. More likely in a “low oil level” situation is for the camshaft, lifters, or camshaft variable timing actuator to fail due to inadequate oil pressure and lubrication.
Can I replace my own camshaft position sensor?
It may be easiest to remove and replace the camshaft sensor from under your vehicle, but it can also be done from the top by removing the air filter housing.
There are two types of Camshaft Sensors, Magnetic, and Hall-effect.
How long does it take to fix a camshaft position sensor?
A camshaft sensor is one of the essential parts of your vehicle, so much so that you probably won’t be able to drive at all with a faulty one. Fortunately, the part is relatively inexpensive compared with a lot of other vehicle parts, and it only takes about an hour or so for a mechanic to replace it.